Expt 2. Acid/Base
Extraction, Mass Spectrometry, and C-13 NMR
Part 2 - Mass
Spectrometry and C-13 NMR
Background
Nuclear magnetic resonance (NMR) is the most important characterization tool
available to organic
chemists. In this lab you will obtain a
C-13 NMR spectrum of each compound
from part 1 in
order to provide evidence that it is the
expected compound.
Mass
spectrometry (MS) is another very
important method to help prove the
structure of a compound. In this lab you
will use a relatively new type of mass
spectrometry, ASAP-MS, to verify
the molecular weights of your isolated
compounds from part 1. You will also carry out mp
determinations of the obtained solids from part 1 both
as a way to confirm their identities and to assess their
purity.
Much
more background information about both
of the above spectroscopic techniques
(NMR and MS) can be found in the Mohrig
and Klein textbooks and the instructor
will fill in needed details during
lecture and at the start of the lab. You
will not find anything about ASAP
ionization in your textbooks so here is
a reference that explains how ASAP
works. https://www.chem.pitt.edu/facilities/mass-spectrometry/mass-spectrometry-introduction
Pre-Lab
In your prelab include
a prediction of the number of peaks expected in the C-13
NMR spectrum of all three components of the original
mixture.
Also make sure to
install the JEOL Delta software on your laptop according
to the directions at http://course1.winona.edu/tnalli/f18/NMR.html
Experimental
Procedures
Melting
Point Determination
Obtain
the mp range of each solid you obtained from part 1.
Make sure to follow all of the precautions necessary
for a sharp mp to be obtained as learned in expt 1.
Also be careful to record your observations during the
melting process and to document the rate of
temperature increase in your lab notes.
C-13 NMR
Spectroscopy
There will
only be enough time for you to obtain the spectrum
of one of your three isolated compounds. Each lab
group will be assigned a specific compound and we
will share data between groups so as to be able to
report spectra for all three compounds.
Please note
that you will be expected to obtain NMR spectra many
times in this course and eventually be able to
obtain them unassisted. Therefore, you should take
careful notes on the procedures you use in this lab.
Preparing the NMR Tube.
- NMR tubes and
solvents are very costly so please be very careful
with the tubes and do not waste the solvent. Also,
be very careful when capping and uncapping
your NMR tube. The tubes are very fragile and the
caps are tight so it is easy to break a tube in the
process of capping or uncapping it.
- Use a Pasteur
pipet to add a small amount of your product to your
NMR tube. For C-13 NMR a good amount of compound is
needed to obtain a useful spectrum in the time
available to us, so make sure the height of the
liquid in the tube is at least 1 cm. (For H-NMR we
will use much less.)
- Add the NMR
solvent, CDCl3, to a height
of approx 5 cm in the tube. Cap and then
invert and/or agitate the tube in order to dissolve
the liquid in the solvent (warning - the caps can
leak).
Obtaining the C-13 NMR
Spectrum. The instructor will assist you in
obtaining the NMR. The basic steps are;
Place tube
in spinner and adjust height.
Place tube
with spinner at top of magnet.
Then use the Delta software to...
Lower the
tube and spinner into the magnet.
Check that
tube is spinning and the correct solvent is selected.
Lock and
shim the sample.
Set up the
desired experiment (in this case C-13) with a file
name of your choosing.
Submit the
experiment.
Eject the
tube from the magnet.
Disposal and Clean Up.
- NMR sample
solutions should be drained into the waste solvent
container. Be very careful when removing the
plastic cap as it is easy to break the top of the
tube when doing so. Rinse the tube several
times with acetone into the waste solvent container.
Store the tube uncapped so the acetone will fully
evaporate by the time of its next use.
Mass
Spectrometry
The mass
spectrometer is in SLC 335. Simply bring your
compound to this room when given the go ahead and
the instructor or TA will assist you in obtaining
the atmospheric solids analysis probe (ASAP) mass
spectrum.
Product
Submission - Submit your solid "products" in
fully labeled 2"x2" ziploc bags. (See the lab report
guidelines.)
Post-Lab
NMR
Processing. General Instructions for Using Delta
- The NMR is
set to save data files directly to our class-storage
readonly folder T:\20203000878M\ReadOnly.
(See http://course1.winona.edu/tnalli/f19/NMR.html
for information about how to access your NMR data
files.
- Once you find
your data file copy it to your desktop (or other
preferred folder on your computer). Then double
click on it to open it in Delta.
- To annotate
the spectrum with peak chemical shifts use the "Auto
Peak Pick" icon.
![peakpick icon](peakpick.jpg)
- Use the zoom
tool (looks like a magnifying glass) to zoom in as
necessary by simply clicking and dragging on the
spectrum. Clicking and dragging in the gray area
below the x-axis just zooms in along the x-axis with
the y-axis remaining at full scale. Use the keyboard
key "hyphen" to revert to the previous (unzoomed)
view.
- Print the
spectrum by simply clicking on the icon that looks
like a printer and selecting the desired printer
from the scroll list.
- The
instructor will provide more detailed instructions
in lecture.
|